Gas stoves are inseparable from each of our family kitchens. After we have chosen the gas stove for a long time, there will be some minor problems that directly affect our lives. So everyone knows what is the maintenance method of Electrolux gas stove? Everyone is not very familiar with it! Today, Xiaobian will take a look at the Electrolux gas stove repair method and maintenance points! Electrolux gas stove repair method 1. There is a phenomenon of separation from fire or fire: at this time it is very likely that the damper is too small, and it is ok to adjust the damper. Or because the pressure of the gas stove is too high, this time you can adjust it properly. If you can't solve it, you need to solve the problem with the professional chef of the gas stove repair. 2. Other phenomena: Sometimes there is no long-term open flame, or the flame is too small, this needs to change the position of the outlet pipe. There is also the need to pay attention to, if you do yourself to repair the gas stove, you must figure out the gas stove signal and some basic information. 3, there is a slight tempering phenomenon: this is likely to make the air pressure too low, just need to increase the degree of the valve can be. Or the design is somewhat unreasonable, the diameter of the fire hole is too large, and the space used is too small. 4, there is air leakage or odor: this time you need to check whether the air pipe is broken, or the joint of the valve is aging, need to be replaced in time, or not burning, directly from the new fight. 5, the air pressure is too high, there is an impact on the electric spark: this time only need to do a simple adjustment of the gas source, reduce the pressure. The output cable is broken and needs to be close to fire: replace a new one, this can't be done. 6. The power cord is loose or there is a large area of ​​damage to the internal structure of the igniter: directly replace the igniter. There is no voltage in the pulse igniter: you need to install a new battery or replace the battery directly. 7. The nozzle of the ignition is too large, which has an effect on the spark: a nozzle can be replaced; the nozzle of the hose has foreign matter: it is better to clean it up. 8, the pulse ignition switch has a slight contact failure: as long as the simple repair or replace the switch just fine. Insufficient air pressure in the air supply switch: You can see if the gas company is out of gas. The ignition cable is not linked to the head: just glue it with glue or tape. Electrolux gas stove repair points 1. If the battery is dead or has poor contact, you can deduct the battery and reinstall it once, to ensure that the contact surfaces of the battery are clean, and then fire again to see the situation. If it is still turned off, you can replace the block battery and try again. 2, look at the dirty eye on the other side, the flame in the middle can not burn the probe, you must burn the probe to fix the fire. There are still some points, you can hold down for ten seconds, in the loose switch, the probe is thermal induction, to be hot, in order to fix the fire. 3, after the fire is hit, do not let go through the small organs on the switch to hold the valve of the magnetic valve, when the thermocouple reaches a certain temperature, let go, usually more than 30 seconds to a minute. 4. Maybe the electric heater can't eat the flame. You need to adjust the damper under the gas stove to make the fire bigger. This allows the electric thermocouple to eat the flame to receive the heat and then transfer the heat. If it doesn't work, insert the electric thermocouple into the flame direction. Take a look, pay attention to the force should not even break the electric thermocouple, but also pay attention to cleaning the electric thermocouple so that he can better transfer heat. 5. The feedback loop of the gas stove is not smooth, to ensure the continuous combustion, and the feedback circuit must be ensured. The feedback parts of the gas stove are set in the place where the flame can be directly burned. When the flame is normal, the feedback loop will provide continuous supply to the pulser. The signal of the gas, otherwise, the pulser will close the solenoid valve. There are many problems that we need to pay attention to when we choose a gas stove, and learning to repair it is a key issue. The above is the small number of Electrolux gas stove repair methods and maintenance points introduced for you today. It is over here. For more information, please continue to pay attention to the decoration home. More related wonderful reading: Electrolux gas stove advantage Electrolux gas stove repair method Lounge Chair For Leisure,Leisure Armchair,Trail Outdoor Leisure Chair,Modern Leisure Chair Foshan Zheng Nengliang Home Furnishing Co., Ltd. , https://www.housecustomax.com
