Ultraviolet ozone cleaning can remove: How to say "ultra" clean? Working principle of ultraviolet ozone cleaning: * Note 1: White alumina will turn yellow when exposed to UV energy. This phenomenon is due to the substrate absorbing UV energy, not a coating. This alumina will change to its original color when heated. Key features: Diamond Painting, also known as Diy Diamond Painting, is an organic combination of exquisite and shining artificial crystal flat-bottomed round diamonds (some square diamonds) and well-designed patterns. Paste it on the corresponding color point on the canvas, thus completing the paste of a diamond, you can get started in a few minutes, and then slowly fill in each color area, a 40CM*40CM diamond painting only takes 2 hours It's done in about a minute. With the continuous development of diamond painting, it has now extended to innovative products such as 3D diamond painting and 5D diamond painting. Diamond Painting,5d Diamond Painting,Diy Diamond Painting Dongguan Junkai Packaging Products Co., Ltd , https://www.diystoragecases.com · Very clean surface · Room temperature operation · Fast and efficient · Simple operation · Ultra-low cost · Two sizes available · 110V or 220V Features:
Skin oil, silicone oil and oil, flux, residual photoresist, glue solvent, carbon, etc.
Contact angle measurement method 4-5 degrees. Apply AES and ESCA to measure subtle peaks. Using the steam test, a uniform rainbow-colored stripe was formed during condensation and evaporation. Normally, after using the cleaning or ultrasonic cleaning process, cleaning the critical surface is considered complete. UV ozone cleaning provides a new cleaning standard. The application of UV cleaning is added after the traditional cleaning process, and the improvement of product performance and reliability constantly proves the value of this new cleaning standard.
The core of the UVOCS cleaning equipment is a low-pressure quartz mercury lamp, which generates ultraviolet light in the range of 254 and 185 nm. Ozone and plasma oxygen are produced, and organic pollutant molecules are excited or decomposed after absorbing 254nm wavelength ultraviolet light. Excited organic pollutants can react with plasma oxygen atoms to form gases, such as CO2, H2O, etc. The entire process takes place at room temperature ** and only takes 1 to several minutes to complete.
** Note 2: The temperature rise of the cleaning element depends on the length of the cleaning process. In most applications, the component temperature can be regarded as room temperature.
· Intermittent bulb working mode. Lights and timers are triggered by closing the door.
· Skid parts tray-smooth-low vibration, ball bearing system-up to 1.5 inches in height.
· Sturdy and durable, all stainless steel structure · Long life. The low-pressure quartz mercury vapor lamp emits 254nm and 185nm UV to promote rapid oxidation and remove trace organic residues.
· Comprehensive UV protection makes equipment operation safer.
· Lower equipment purchase cost and operation cost.
· 0-999 second / minute / hour timer, can be accurately controlled. The lights and timer are triggered by the door closing.
Ozone exhaust shield: The UVOCS tray model has an ozone shield that allows UVOCS cleaning equipment to be placed on your production line or equipment, and process related equipment. This will minimize recontamination of the material. A 3-inch exhaust outlet is built into the back of the shroud and can be connected to your exhaust system. No exhaust fan is provided. The minimum displacement requirement is 100 CFM. (Cubic feet per minute)
· There is a beep at the end of the operation process.
· UV "ON" indicator and visible window.
· Simple operation: set the timer, open the door, draw out the tray, and place the components on the tray. Slide the tray in and close the door. There is a beep at the end of the cleaning operation. Open the door and remove all cleaning elements.
UVOCS Ultraviolet Ozone Cleaning Machine Gets Ultra Clean Surface
UVOCS ultraviolet ozone (OZONE) cleaning machine-leading scientific laboratory equipment The UV ultraviolet ozone cleaning process provides a simple, economical, fast access to ultra-clean surfaces, removing most inorganic substrates (such as quartz, silicon wafer, gold, nickel , Aluminum, gallium arsenide, aluminum oxide *, etc.). Especially when the substrate and the thin film evaporation need to be well bonded, UV cleaning is ideal. To obtain an ultra-clean surface, you only need to use ultraviolet ozone cleaning process for a few minutes after the traditional cleaning.